Important Note:
1 The Wifi Switch must be kept connectting with your house wifi router service at any time. It can't send wifi signal by itself.
2 You can use your phone to control it by APP eWeLink in 2G/3G/4G network after finish set up.
Packing List:
1 X 4 Way WIFI Switch
1 X Remote Transmitter (build-in a 23A/12V battery)
How to connect phone with switch?
1 Download and install the software of “eWeLink” from APP store or Google play store.
2 Follow “eWeLink” instructions to register an account on it.
3 Log in your account of “eWeLink”.
4 Press "switch1 button" (Or Switch2, Switch3, Switch4) for 5 seconds until you see the D2 light flash 3 times quickly and 2 times slowly, then release it.
5 Add device on mobile phone by eWeLink APP according its introduction.
Features
1 Support WIFI network. (Attention: The switch module must always be kept connecting with wifi router service.)
2 Support 433mhz RF remote transmitter control.(Can learn most 433.92mhz remote code, like chip 2260,2262,2264,1527. Allow 16 different remote codes to control )
3 Support three working modes: momentary, interlock(latching) and self-lock(toggle) control.
4 Support Max 8 timing tasks for each added device.
5 Support status tracking, home appliances status timely feedback to your App.
6 The remote battery is: one CR2025 button battery (not include)
Product Specification:
1 Input voltage: AC 85-265V
2 Maximum load: 10A
3 Working temperature: 0-60 centigrade
4 Control method: WIFI +433mhz RF + Manual Button Control
5 Channels: 4 Way
6 Switch size: 116*90*42mm
7 Active output, AC85-265V.
How to connect phone with switch?
1 Download and install the software of “eWeLink” from APP store or Google play store.
2 Follow “eWeLink” instructions to register an account on it.
3 Log in your account of “eWeLink”.
4 Press switch 1 button (Or Switch 2, Switch 3, Switch 4) for 5 seconds until you see the D2 light flash 3 times quickly and 2 times slowly, then release it.
5 Add device on mobile phone by eWeLink APP according its introduction.
How to learn 433mhz transmitter?
Step 1: Supply power to switch receiver
1 Press “learning button” until you see LED flash 1 time, release button, then CH1 learn.
2 Press “learning button” until you see LED flash 2 times, release button, then CH2 learn.
3 Press “learning button” until you see LED flash 3 times, release button, then CH3 learn.
4 Press “learning button” until you see LED flash 4 times, release button, then CH4 learn.
Step 2: Cut off power, and keep pressing "learning button", then supply power, when the LED flash 3 times then release button.
OK! You can use remote to control the switch now.
How to clear 433mhz signal?
Step 1: Keep pressing the "learning button" ;
Step 2: Supply power to switch;
Step 3: The LED light will flash 4 times slowly.
Step 4: Release the "learning button". OK
How to set working mode?
Supply AC 85-250V power to the relay.
1: Press mode button until you see D3 flash 3 times, release button, now it is self-lock or toggle
2: Press mode button until you see D3 flash 2 times, release button, now it is inter-lock or latching.
3: Press mode button until you see D3 flash 1 time, release button, now it is momentary.
What is the difference between working mode?
1 Self-lock (toggle): Press remote button A , receiver CH1 ON. press button A again, then receiver CH1 OFF
2 Inter-lock (latching): Press remote button A , receiver CH1 ON, and receiver CH2,CH3,CH4 OFF.
3 Momentary (Jog): Press button A, receiver CH1 ON. 1 seconds later, the receiver CH1 OFF.